Saturday 25 May 2013

A Review of Instant Mold.


Today I present a review and tutorial on the product Instant Moud, I bought this product Online from Firestorm Games in Cardiff (though they seem to be out of stock at the moment)

So, What is it?


Instant Mold is re-usable putty with the texture of a Glue Stick like you would use in a hot glue gun, It is sold under the non brand name of Oyumaru. It softens with very hot water to the texture of blue tac (U.S. - fun tack), whilst warm you can press it over details of miniatures or models or ANYTHING and it will take a negative print from it, it then takes about a minuet to cool. When cool you can remove it from the moulded object and fill the resulting negative with a putty of you’re choice to create a copy, when the putty is cured you can remove the replica and either cast another or drop the Instant Mold back into hot water and use it again!


How much does it cost?

I picked mine up for about £10.00 for 6 strips, which are of course re-usable.


How much detail is copied?

All of it, or at least 99%, it may take a few attempt to get all of the air bubbled from the negative when placing in your putty


Can I fill a negative with resin?

No, most resins heat up as they cure so it would distort the mould.


What are the moral implications of Stealing Detail?

Well, this is a biggie, IT IS WRONG, ILLEGAL AND IMMORAL TO RIP OFF OTHER PEOPLES HARD WORK!  But there are a few reasons to give it a go. I have chosen the following example to justify my use of the product.

Vinyl Tyres on plastic kits – We all know the horror of track rot, I can’t help with this but I can offer a solution to vinyl tyres.

1 – Take a tyre and work out which way it will go on the kit, you want the outside of the tyre UP so it will be pushed into the mould.


2 – Warm up the Instant Mold as per pack instructions and push over the tyre making sure that it pushes tightly into the middle of the Tyre


3 – Allow to cool for 1-2 minuets
4 – Remove the negative from the tyre and mix up your putty of choice (I chose Green stuff)


5 – Fill the negative with your putty, use water to stop the putty sticking to your fingers as putty will not stick to Instant Mold


6 – let your putty cure for 6 or so hours until set.
7 – Remove your cast from the mould and there you have it, A tyre that will not rot over time


Bare in mind that this process has taken 6 hours and made 1 tyre, how many tyres are on a typical truck 6? 10? Or more so you may want to make more than 1 negative mould to hasten the process


What else have I used it for?

I needed a load of crates for decorating AT and AA gun bases, so I cast a load of the plastic boxes that come with PSC Zis2/3 AT guns for this purpose, I do not see a problem with this so long as I do not plan so sell the cast items or pass them off as my own work,


I have also added cloaks to Zvezda Russians by casting one from an Elhiem Russian with PpsH. I created the mould in the usual way by pushing it onto the cloak, but then I filled it with less putty than I needed and pushed the Zvezda Russian into it while un-cured. I left it to cure fully before removing the mold, I then had to add the front of the cloak using putty and regular sculpting to hide the joins.



What do I think?

I do enjoy using this product and highly recommend it, when I first used it I added new 3D shield designs to my WFB Dark Elves and I have loved using Instant Mold for all sorts of things since.

There are more uses than I could possibly list here, have a go but PLEASE…
DO NOT COPY WHOLE AREAS!
DO NOT SELL CAST PIECES!
AND BE CAREFUL, THE OWNER OF THE ORIGINAL MAY HAVE EVERY RIGHT TO ASK YOU TO STOP!
BUT MOST OF ALL……….HAPPY MODELING!

Mike

9 comments:

  1. This stuff looks great, never heard of it before. Thanks for this review, I'll buy this myself.

    ReplyDelete
    Replies
    1. Do a search for - Oyumaru - it may be easier to find in Germany

      Delete
  2. Seriously cool, I'm getting some to copy some of my conversions - I read somewhere that if you change 20% of the original then it's okay :)

    ReplyDelete
  3. I saw this recently on another blog (about a week ago) Looks really good. You´ve made a Nice Review :-D

    ReplyDelete
  4. That stuff is easy to find at ebay.
    I have used already (but the figures didn't come out that good).

    ReplyDelete
  5. Thanks everyone, I think that is a successful first review, one thing I must add is that It is best to copy areas that will have a flat back, i.e. vehicle stowage or a shield, this way you can hide the un-detailed back.

    Mike

    ReplyDelete
  6. We are introducing an upgrade version of this instant mold. We call it Blue Stuff Mold.
    We have modified the formula to make it more accurated and to keep it soft for longer time to allow you to create a better mold.

    Other remarks:
    - 2 Formats: Small with 4 pieces and Standard with 8. Cheaper and better than this American product.
    - As it is being produced in Europe, it is cheaper to delivery in Europe.

    You will be able to get it from www.greenstuffworld.com

    Hope this helps.

    ReplyDelete
    Replies
    1. Excellent news, thanks for sharing.
      It's good to know that technology is moving forward in this area, I'll get some ordered when it's released and run another review along with a comparison, If you have no objections.

      Delete